Para comparar : Balanzas de precisión PS 3000.3Y

Deutsch English Español Français Italiano Polski Türkiye Česky USA 中文

Español

‹‹ Productos Novedades Sobre empresa

Pagina principal > Productos > Balanzas de laboratorio > Balanzas de precisión > Balanzas de precisión PS 3Y > Balanzas de precisión PS 3000.3Y

Balanzas de precisión PS 3000.3Y

This image is for reference only.

Código de producto: WL-220-0073

CE - Simboliza la conformidad del producto con las normas de la Unión Europea, que se aplican al uso de este producto, colocar el marcado CE de un producto es una declaración de la persona responsable de que el producto cumple con las normas generales de seguridad establecidos en las directivas de la marca CE.

Preguntar sobre producto

Funciones

Autotest

Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.

Dosing

Weighing process for which reference mass has been determined together with tolerance for its determination. Dosing tolerance is given in [%] and it is calculated in relation to the reference value thus being a permissible deviation of this process. This solution is used for weighing powders, liquids and loose materials. Dosing function performance is often supported with bargraph - load indicator. For industrial scales it is possible to use a control systems of dosing process.

Percent Weighing

Percent Weighing function is used for comparision of measured products with mass standard. Mass of a mass standard may be a numeric value taken from a database or it may be determined through a measurement process. Each measured product is compared to mass standard, mass of which is presumed as a model 100% ideal mass. For products weighing less than the mass standard, obtained results are lower than 100%, for products weighing more, the obtained results are greatly exceeded.

Parts counting

Function using mass measurement for determination of measured items quantity. Mass of a single item is required for this process. It may be either estimated through weighment or taken from a database. For items counting the following algorithm is used: all items mass / single item mass = quantity. Function operation is supperted by a mechanism of Automatic Correction of Accuracy. This allows to update single item mass in course of the process. To a certain extend Automatic Correction of Accuracy eliminates error which may be a result of different mass values of seemingly alike single elements. For industry solutions items counting may be simultaneously carried out with checkweighing and dosing thus industry solutions feature audio signalling base informing that specified number of items has been weighed. It is possible to apply weighing systems using few platfroms of different MAX capacities and different accuracies.

Formulation

Function supporting the mixture making process, wherein the mixture contains various components. Formulation function usually uses the balance/scale database of components. Formulation serves for monitored checkweighing of every single component with a given tolerance. It is enriched with a set of individual settings.

Statistics

Statistiscs function registers and analyses performed measurements. This supplies the user withthe following information: Max and Min standard deviation, average value, variance, range et.

Checkweighing

Checkweighing function is used for checking whether the measured sample mass is within the predefined threshold values, Low [LO] and Hgh [HI]. The thresholds are given in [g] and [kg] units. Current state of a sample being measured is signalled by means of pictorgams located on a display for laboratory balances, for industrial scales Stackligt System is used. This visual +/- inspection is in operation during segregation, control or packing process of products for which mass has bees determined with a specifaied tolerance, eg. 12860 g 961

IR sensors

Programmable function supporting the weighing process through control of the following options: sliding weighing chamber doors, printout, zeroing, tarring etc. Especially appreciated wherever preventing the balance from soiling is important.

Under-pan weighing

The solution enables weighing with use of a stand, which is advisable for loads of non-standard shapes and dimensions and those that generate magnetic field.

GLP Procedures

Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.

Animal weighing

Process of mass determination for a product which may unwillingly reposition within the weighing pan. Mass determination in such cases requires much longer period of time when compared to typical weighing process. It is the user who defines period of time needed for control of measured product mass. The user can thus optimize the function depending on the measured product characteristics.

Density determination

Liquid or solid body density function uses the Archimedes principle and it requires a special kit to be applied. The kit when used, replaces a weighing pan. For solids mass of the sample must be determined first in the air, next in the liquid of specified density. For liquids the so called sinker, density of which has been determined, must be measured first in the air, next in the tested liquid. The density determination process is disturbed by air bubbles which may stick either to the measured sample or the sinker. In case of laboratory equipment very light solids may be measured. For industry, solid bodies density may be determined by means of under-pan weighing. Tested load of significant size may be measured this way.

Differential weighing

Differential weighing informs about mass variation a particular sample, wherein the said variation is a result of manufacturing processes.

Differential weighing is often applied in product control process, for which reference product parameters have been specified in order to be used as a source of comparison for the whole series.
Insuchcasestandard deviation is the information which tells about quality and completeness of a final product. For systems based on a feed-back technique such information may be used by control units.

Statistical Quality Control

Statistical control for determination of basic statistical criteria: maximum, minimum, standard deviation, mean values for each batch, etc.

h3{display:inline color:inherit font-weight:inherit}La balanza PS 3Y es una balanza de laboratorio, equipada con una pantalla táctil LCD de color de 5.7 Ofrece posibilidades completamente nuevas en el alcance del servicio y la presentación de resultados de medición. La personalización de la balanza se lleva a cabo utilizando el perfil del usuario. Un elemento estándar de la balanza es el sistema de ajuste automático con un patrón interno. El control de nivel se realiza mediante el sistema LevelSENSING, que utiliza un sistema de nivel electrónico especial patentado por RADWAG. La novedad en estas balanzas es la capacidad de monitorear las condiciones ambientales en línea a través de sensores internos o un módulo externo THB-S. Amplias bases de datos permiten el registro de todas las mediciones con la opción de imprimir y exportar. Gracias a las impresiones estándar y editables por el usuario, es posible crear la documentación requerida por GLP / GMP en prácticamente cualquier área. El modo de control de peso independiente se implementa en cooperación con el alimentador automático PA-04 / H.

Maxima capacidad	3000 g
Minima cacacidad	20 mg
Legibilidad [d]	0,001 g
Rango de tara	-3000 g
Pesada mínima usp	1 g
Pesada mínima	0,1 g
Repetibilidad (Max)	0,0015 g
Repetibilidad (5% Max)	0,0005 g
Linealidad	±0,004 g
Tiempo de estabilización	3 s
Calibración	interna (automatica)
Pantalla	5,7” resistivo color touchscreen
Conectividad	2×RS232, 2×USB-A, Ethernet, 4 IN / 4 OUT (digitales), Wi-Fi^®
Alimentacion	100 ÷ 240 V AC 50 / 60 Hz
Consumo máximo de potencia	10 W
Temperatura de trabajo	+10 ÷ +40 °C
Dimensión de platillo	128×128 mm
Dimensiones de embalaje	716×360×260 mm
Masa neto	5,7 kg
Masa bruto	8,3 kg

La repetibilidad se expresa como una desviación estándar de 10 posiciones de carga.
El tiempo de estabilización depende de las condiciones externas y la dinámica de colocar los pesos en el platillo; especificado para el perfil FAST.