Español

Productos Novedades Servicios Soporte Noticias Sobre la empresa Contacto

‹‹ Productos Novedades Sobre empresa

Pagina principal > Productos > Balanzas de laboratorio > Balanzas de precisión > Balanzas de precisión PM 4Y > Balanza de precisión PM 60.1.4Y

Balanza de precisión PM 60.1.4Y

This image is for reference only.

Código de producto: WL-223-0011

CE - Simboliza la conformidad del producto con las normas de la Unión Europea, que se aplican al uso de este producto, colocar el marcado CE de un producto es una declaración de la persona responsable de que el producto cumple con las normas generales de seguridad establecidos en las directivas de la marca CE.

Preguntar sobre producto

Funciones

Autotest

Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.

Dosing

Weighing process for which reference mass has been determined together with tolerance for its determination. Dosing tolerance is given in [%] and it is calculated in relation to the reference value thus being a permissible deviation of this process. This solution is used for weighing powders, liquids and loose materials. Dosing function performance is often supported with bargraph - load indicator. For industrial scales it is possible to use a control systems of dosing process.

Percent Weighing

Percent Weighing function is used for comparision of measured products with mass standard. Mass of a mass standard may be a numeric value taken from a database or it may be determined through a measurement process. Each measured product is compared to mass standard, mass of which is presumed as a model 100% ideal mass. For products weighing less than the mass standard, obtained results are lower than 100%, for products weighing more, the obtained results are greatly exceeded.

Parts counting

Function using mass measurement for determination of measured items quantity. Mass of a single item is required for this process. It may be either estimated through weighment or taken from a database. For items counting the following algorithm is used: all items mass / single item mass = quantity. Function operation is supperted by a mechanism of Automatic Correction of Accuracy. This allows to update single item mass in course of the process. To a certain extend Automatic Correction of Accuracy eliminates error which may be a result of different mass values of seemingly alike single elements. For industry solutions items counting may be simultaneously carried out with checkweighing and dosing thus industry solutions feature audio signalling base informing that specified number of items has been weighed. It is possible to apply weighing systems using few platfroms of different MAX capacities and different accuracies.

Formulation

Function supporting the mixture making process, wherein the mixture contains various components. Formulation function usually uses the balance/scale database of components. Formulation serves for monitored checkweighing of every single component with a given tolerance. It is enriched with a set of individual settings.

Newton unit measurement

Function allowing to perform the measurement in Newton unit, it may be used for processes aiming to determine force resulting in the sample damage.

Statistics

Statistiscs function registers and analyses performed measurements. This supplies the user withthe following information: Max and Min standard deviation, average value, variance, range et.

Checkweighing

Checkweighing function is used for checking whether the measured sample mass is within the predefined threshold values, Low [LO] and Hgh [HI]. The thresholds are given in [g] and [kg] units. Current state of a sample being measured is signalled by means of pictorgams located on a display for laboratory balances, for industrial scales Stackligt System is used. This visual +/- inspection is in operation during segregation, control or packing process of products for which mass has bees determined with a specifaied tolerance, eg. 12860 g 961

IR sensors

Programmable function supporting the weighing process through control of the following options: sliding weighing chamber doors, printout, zeroing, tarring etc. Especially appreciated wherever preventing the balance from soiling is important.

GLP Procedures

Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.

Animal weighing

Process of mass determination for a product which may unwillingly reposition within the weighing pan. Mass determination in such cases requires much longer period of time when compared to typical weighing process. It is the user who defines period of time needed for control of measured product mass. The user can thus optimize the function depending on the measured product characteristics.

Air density correction

Function performing correction of mass measurement indication, wherein the air density is taken into account. It is used in balances with reading unit < 0,01 mg.

Differential weighing

Differential weighing informs about mass variation a particular sample, wherein the said variation is a result of manufacturing processes.

Differential weighing is often applied in product control process, for which reference product parameters have been specified in order to be used as a source of comparison for the whole series.
Insuchcasestandard deviation is the information which tells about quality and completeness of a final product. For systems based on a feed-back technique such information may be used by control units.

Replaceable unit

Replaceable units.

Statistical Quality Control

Statistical control for determination of basic statistical criteria: maximum, minimum, standard deviation, mean values for each batch, etc.

Las balanzas de la serie PM están equipadas con un innovador sistema de medición basado en la tecnología RADWAG MonoBLOCK^®. Esto permite un funcionamiento con una capacidad de lectura de 0,01 g a una capacidad de 15 kg y una capacidad de lectura de 0,1 g a una capacidad de 50 kg. El uso del nuevo sistema de medición, objeto de la patente RADWAG, garantiza la estabilidad de la repetibilidad en el tiempo a un intervalo sd <1d. La única solución del sistema de medición se caracteriza por su gran resistencia al cambio de las condiciones ambientales. Un sistema de protección de 4 puntos incorporado evita la sobrecarga de balanza, lo que garantiza la seguridad en caso de carga demasiado pesada se aplica sobre el platillo de pesaje. Principales características: Nuevo sensor RADWAG MonoBLOCK^® Repetibilidad sin igual de las indicaciones Pesaje de cargas pesadas con la máxima precisión Operación intuitiva garantizada por una pantalla táctil de color Cumplimiento con CFR21 Mediciones de masa rápidas Diseño mecánico robusto - nueva plataforma de pesaje inferior Ergonomía mejorada - dos tipos de terminal de pesaje para la selección. La balanza ofrece la posibilidad de pesar cargas fuera de la plataforma de pesaje (llamado pesaje por debajo de la balanza). Esta es una alternativa para pesar cargas con dimensiones y formas no estándar o aquellas que generan campo magnético.

Maxima capacidad	60 kg
Minima cacacidad	-
Legibilidad [d]	1 g
Rango de tara	-60 kg
Repetibilidad (5% Max)	0,4 g
Repetibilidad (Max)	0,8 g
Linealidad	±3 g
Pesada mínima	82 g
Pesada mínima usp	820 g
Tiempo de estabilización	3 s
Calibración	interna (automatica)
Pantalla	5,7” resistivo color touchscreen
Communication interface	2×RS232, 2×USB-A, Ethernet, 4 IN / 4 OUT (digitales), Wi-Fi^®
Alimentacion	100 ÷ 240 V AC 50 / 60 Hz
Consumo máximo de potencia	0,5 A
Temperatura de trabajo	+10 ÷ +40 °C
Dimensión de platillo	400×500 mm
Dimensiones de embalaje	700×600×200 mm
Masa neto	17 kg
Masa bruto	19 kg

Documentación técnica

Publicaciones y materiales didácticos

User Manual
(3.76 MB) EN

Data Sheet
(0.18 MB) EN

Data Sheet
(1.26 MB) EN

Conformity Declaration
(0.04 MB) EN

Perfiles Definidos
(1.65 MB)

Sistema THBR 2.0
(5.24 MB)

PM - Balanzas de Precision Para Altas Capacidades
(0.48 MB)

Balanza de precisión PM 60.1.4Y

balanza

Nivel electrónico

Intercambio de datos (puerto USB)

Sensores infrarrojo

Interfaces

Autotest

Dosing

Percent Weighing

Parts counting

Formulation

Newton unit measurement

Statistics

Checkweighing

IR sensors

GLP Procedures

Animal weighing

Air density correction

Differential weighing

Replaceable unit

Statistical Quality Control

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

Accesorios

RADWAG Balanzas Electrónicas