Präzisionswaage PS 250.3Y

Präzisionswaage PS 250.3Y - RADWAG Elektronische Waagen
This image is for reference only.

Produktcode: WL-220-0029
Kontaktformular

Beschreibung

Wägebereich [Max]: 250g
Ziffernschritt [d]: 0,001g

Die PS 3Y Präzisionswaage ist eine Laborwaage mit einem farbigen 5,7" LCD Touchscreen-Display. Das Display bringt neue Möglichkeiten im Bereich der Bedienung der

Waagen

und der Präsentation der Messergebnisse. Die Personalisierung der

Waage

erfolgt über das Benutzerprofil.
 
Zur Standardausrüstung der

Waage

gehört das System der automatischen Justierung mit einem internen Prüfgewicht . Die Nivellierungsüberwachung wird durch das LevelSENSING-System realisiert, das ein spezielles, durch RADWAG patentiertes System der elektronischen Libelle verwendet. Eine Neuheit ist die Möglichkeit der On-line-Überwachung der Umgebungsbedingungen durch interne Sensoren oder ein externes THB-S.
 
Die Datenbanken ermöglichen das Erfassen sämtlicher Messungen sowie das Drucken und den Datenexport. Standardausdrucke sowie benutzerdefinierte Ausdrucke dienen dem Dokumentieren gemäß GLP/GMP praktisch in jedem Einsatzbereich. Die unabhängige Betriebsart der Kontrolle der Masse erfolgt mit Hilfe des automatischen Transporters PA-04/H.

Videos

Merkmale

Elektronische Libelle
Funktionalität:
- ALARM
- graphische Nivellierungsanzeige
- programmierbare Toleranzen

Elektronische Libelle

Funktionalität:
- ALARM
- graphische Nivellierungsanzeige
- programmierbare Toleranzen
Datenaustausch (USB)
- Softwareupdates
- Export von Wägedaten
- Export/Import von Datenbanken
- Export/Import von Waageneinstellungen
- Datenaustausch zwischen Waagen

Datenaustausch (USB)

- Softwareupdates
- Export von Wägedaten
- Export/Import von Datenbanken
- Export/Import von Waageneinstellungen
- Datenaustausch zwischen Waagen
Infrarotsensoren
Funktionalität:
- PRINT-Funktion
- TARA-Funktion

Infrarotsensoren

Funktionalität:
- PRINT-Funktion
- TARA-Funktion
Kabellose Kommunikation
Optionale Ausführung:
Kabellose Kommunikation der Wägekammer mit dem Terminal.

Kabellose Kommunikation

Anwendung:
1. Beseitigung von zusätzlichen Vibrationsquellen Ein Standort des Terminals außerhalb des Wägetisches beseitigt Vibrationen, die bei der Bedienung entstehen. Dies ermöglicht einen stabilen Betrieb bei höchsten Auflösungen ohne Anwendung von speziellen Wägearbeitsplätzen.
2. Bequemes und komfortables Wägen unter Abzügen und auf Sicherheitswerkbänken Die kabellose Kommunikation des Terminals mit dem Wägemodul ermöglicht den Betrieb der Laborwaage unter Abzügen, ein bequemes Arbeiten und mehr Sicherheit.
3. Isolation der Waage von ungünstigen Umgebungsbedingungen Die kabellose Kommunikation ermöglicht das Aufstellen des Wägemoduls in Windschutzschränken oder eine vollständige Isolation vom Bediener. Diese Lösung ermöglicht das Wägen von kontaminierten oder toxischen Substanzen ohne Gefahr für die Gesundheit des Bedieners.
Interfaces
- Ethernet
- 2×USB
- 2×RS 232
- 4 in / 4 out
- WiFi 2,4GHz b,g,n

Interfaces

- Ethernet
- 2×USB
- 2×RS 232
- 4 in / 4 out
- WiFi 2,4GHz b,g,n

Funktionen

Autotest

Autotest

Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.
Dosing

Dosing

Weighing process for which reference mass has been determined together with tolerance for its determination. Dosing tolerance is given in [%] and it is calculated in relation to the reference value thus being a permissible deviation of this process. This solution is used for weighing powders, liquids and loose materials. Dosing function performance is often supported with bargraph - load indicator. For industrial scales it is possible to use a control systems of dosing process.
Percent Weighing

Percent Weighing

Percent Weighing function is used for comparision of measured products with mass standard. Mass of a mass standard may be a numeric value taken from a database or it may be determined through a measurement process. Each measured product is compared to mass standard, mass of which is presumed as a model 100% ideal mass. For products weighing less than the mass standard, obtained results are lower than 100%, for products weighing more, the obtained results are greatly  exceeded.
Parts counting

Parts counting

Function using mass measurement for determination of  measured items quantity. Mass of a single item is required for this process. It may be either estimated through weighment or taken from a database. For items counting the following algorithm is used: all items mass / single item mass = quantity. Function operation is supperted by a mechanism of Automatic Correction of Accuracy. This allows to update single item mass in course of the process. To a certain extend Automatic Correction of Accuracy eliminates error which may be a result of different mass values of seemingly alike single elements. For industry solutions items counting may be simultaneously carried out with checkweighing and dosing thus industry solutions feature audio signalling base informing that specified number of items has been weighed. It is possible to apply weighing systems using few platfroms of different MAX capacities and different accuracies.
Formulation

Formulation

Function supporting the mixture making process, wherein the mixture contains various components. Formulation function usually uses the balance/scale database of components. Formulation serves for monitored checkweighing of every single component with a given tolerance. It is enriched with a set of individual settings.
Newton unit measurement

Newton unit measurement

Function allowing to perform the measurement in Newton unit, it may be used for processes aiming to determine force resulting in the sample damage.
Statistics

Statistics

Statistiscs function registers and analyses performed measurements. This supplies the user withthe following information: Max and Min standard deviation, average value, variance, range et.
Checkweighing

Checkweighing

Checkweighing function is used for checking whether the measured sample mass is within the predefined threshold values, Low [LO] and Hgh [HI]. The thresholds are given in [g] and [kg] units. Current state of a sample being measured is signalled by means of pictorgams located on a display for laboratory balances, for industrial scales Stackligt System is used. This visual +/- inspection is in operation during segregation, control or packing process of products for which mass has bees determined with a specifaied tolerance, eg. 12860 g 961
IR sensors

IR sensors

Programmable function supporting the weighing process through control of the following options: sliding weighing chamber doors, printout, zeroing, tarring etc. Especially appreciated wherever preventing the balance from soiling is important.
Under-pan weighing

Under-pan weighing

The solution enables weighing with use of a stand, which is advisable for loads of non-standard shapes and dimensions and those that generate magnetic field.
GLP Procedures

GLP Procedures

Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.
Animal weighing

Animal weighing

Process of mass determination for a product which may unwillingly reposition within the weighing pan. Mass determination in such cases requires much longer period of time when compared to typical weighing process. It is the user who defines period of time needed for control of measured product mass. The user can thus optimize the function depending on the measured product characteristics.
Density determination

Density determination

Liquid or solid body density function uses the Archimedes principle and it requires a special kit to be applied. The kit when used, replaces a weighing pan. For solids mass of the sample must be determined first in the air, next in the liquid of specified density. For liquids the so called sinker, density of which has been determined, must be measured first in the air, next in the tested liquid. The density determination process is disturbed by air bubbles which may stick either to the measured sample or the sinker. In case of laboratory equipment very light solids may be measured. For industry, solid bodies density may be determined by means of  under-pan weighing. Tested load of significant size may be measured this way.
Differential weighing

Differential weighing

Differential weighing informs about mass variation a particular sample, wherein the said variation is a result of manufacturing processes.

Differential weighing is often applied in product control process, for which reference product parameters have been specified in order to be used as a source of comparison for the whole series.
Insuchcasestandard deviation is the information which tells about quality and completeness of a final product. For systems based on a feed-back technique such information may be used by control units.
Statistical Quality Control

Statistical Quality Control

Statistical control for determination of basic statistical criteria: maximum, minimum, standard deviation, mean values for each batch, etc.

Technische Daten

Wägebereich [Max]

250

 g

Min. Belastung

20

 mg

Ziffernschritt [d]

0,001

 g

Tarierbereich

-250

 g

Wiederholbarkeit (5% Max)

0,0005

 g

Wiederholbarkeit (Max)

0,001

 g

Linearität

±0,002

 g

Min. Einwaage

0,1

 g

Min. Einwaage USP

1

 g

Stabilisierungszeit

2

 s

Justierung

intern (automatisch)

 

Display

5,7” resistiv farbiger touchscreen

 

Schnittstelle

2×RS232, 2×USB-A, Ethernet, 4 IN / 4 OUT (digital), Wi-Fi®

 

Stromversorgung

100 ÷ 240 V AC 50 / 60 Hz

 

Leistungsaufnahme

500 mA (bezprzewodowy terminal - 1A)

 

Umgebungstemperatur

+10 ÷ +40

 °C

Waagschale

128×128

 mm

Verpackungsgröße

716×360×260

 mm

Nettogewicht

5,3

 kg

Bruttogewicht

7,8

 kg

Dokumentation

Technische Dokumentation

Bedienungsanleitung
(4.37 MB) DE

Save
See the publication

Produktfolder PS 3Y
(1.09 MB) DE

Save
See the publication

E2R AUDIT TRAIL CFR21 p.11
(0.18 MB) DE

Zapisz
See the publication

Konformitätserklärung
(0.03 MB) DE

Save
See the publication
Publikationen und Lerninhalte

Zubehör

Granit-Antivibrationstisch
Antivibrationstische für Laborwaagen
Professioneller Wägetisch
Audit Trail Reader

Zubehör

E2R System
Etiketten Editor R02
Datenbasen-Editor 3Y
Parametereditor
R.Barcode

Zubehör

Produktname

Beschreibung

R.Barcode

R-LAB
RAD KEY
RADWAG Development Studio
RADWAG Remote Desktop
LabVIEW Driver
Gestell für Unterflurwägen

Zubehör

Dichtebestimmungsset
Thermische Drucker
Etikettendrucker
Umgebungsbedingungen-Messgeräte THBR 2.0 System

Zubehör

Produktname

Beschreibung

Modul THB P

...

Modul THB S

...

Schutzhauben
Kabel RS 232 (Waage – Drucker EPSON)
Kabel RS 232RS 485
Anschlusskabel für Zigarettenanzünder
Automatische Zuführung

Zubehör

Produktname

Beschreibung

Automatischer Aufgeber PA-04/H

...

Barcodescanner
Schrank für Waagen mit Waagschale 128×128mm
Waagenkoffer
Displays
Netzteile

RADWAG Elektronische Waagen

Torunska 5
26-600 Radom
Polen
Tel.: +48 48 386 63 03
E-mail: export@radwag.com
VAT Nr.: 796-000-03-27
Vimeo Radwag YouTube Radwag Facebook Radwag
© 2019 RADWAG Elektronische Waagen. Alle Rechte vorbehalten.

See our movies
RADWAG

Radwag WEBINARS